Water Sampler & Flow Meter ​Power Options​

Nickel-Cadmium Batteries

Our nickel-cadmium battery is your best choice where a portable power source is needed in continuous-use applications. It allows more charging cycles than Lead-acid batteries and isn't damaged by overcharging or being left totally discharged for extended periods.

  • Maintenance free

  • Ruggedly built

  • Temperature tolerant


 

Model 934 Nickel-Cadmium Battery

​Model 934

​Output Voltage
​12-14 VDC
​Amp/Hour Rating
​4.0
​Connector Type
​2-pin circular Amphenol
​Recommended Use
​Teledyne ISCO samplers, flowmeters, and portable pumps when used at regularly serviced monitoring sites.

 

Lead-Acid Batteries

Teledyne ISCO's lead-acid batteries are best used wherever portable standby power is required. They have a very low self-discharge rate and outperform nickel-cadmium batteries in applications where battery power is used sporadically over long periods of time. All of our lead-acid batteries are environmentally sealed and maintenance-free. Fluid level checks and refilling are not required.

​​
Model 945 Lead-Acid Battery

Model 945

Model 946 Lead-Acid Battery

Model 946

Model 948 Lead-Acid Battery

Model 948

​Output Voltage
​6 VDC
​11-13.5 VDC
​12 VDC
​Amp/Hour Rating
5.0 ​6.5 ​45
​Connector Type
​Coiled Wire
​2-pin circular Amphenol
​2-pin circular Amphenol
​Recommended Use
Sites with intermittent or sporadic activity such as stormwater runoff monitoring, inflow and infiltration (I&I) studies, combined sewer overflow CSO monitoring, and more.

​High-capacity Power Packs

Our rugged, high capacity power packs safely and reliably convert available AC voltage to DC power.

  • Built-in battery charger

  • Environmentally sealed

 

Model 913 High-capacity Power Pack

Model 913

Model 923 High-capacity Power Pack

Model 923

​Input Voltage
​120 VAC
50 or 60 Hz
​240 VAC
50 or 60 Hz
​Output Voltage/Current
​12.5 VDC at 5 A
​12.5 VDC at 5 A
​Connector Type
​2-pin circular Amphenol
​2-pin circular Amphenol
​Recommended Use
​ ​Fixed installation or sites with reliable AC power.


 

Battery-backed Power Packs

Teledyne ISCO's battery-backed power packs assure that your equipment will keep running even if AC line voltage is interrupted.

  • Battery backup

  • Benchmark reliability


 

Model 914 Battery-backed Power Pack
 

Model 914

Model 924 Battery-back Power Pack
 

​Model 924

​Input Voltage
​120 VAC
50 or 60 Hz
​240 VAC
50 or 60 Hz
​Output Voltage/Current
​12-14.5 VDC
3 A continuous
5 A maximum
​12-14.5 VDC
3 A continuous
5 A maximum
​Connector Type
​2-pin circular Amphenol
​2-pin circular Amphenol
​Recommended Use
​ ​Fixed installations or sites with available AC power. This includes sites with an unreliable AC power supply.

Amphenol Connector Chargers

An Amphenol connector charger is a low-cost method for charging single Teledyne ISCO batteries. An impact-resistant case and solid-state construction make these chargers almost indestructible.


 

Model 961 Charger
 

​Model 961

Model 963 Charger
 

​Model 963

Model 965 Charger

​Model 965*

​Input Voltage
​120 VAC at 60 Hz*
​120 VAC at 60 Hz
240 VAC at 50 Hz
​120 VAC at 60 Hz
240 VAC at 50 Hz
​Output Voltage
​14.5 VDC at 400 mA*
​13.7 VDC at 720 mA
​13 VDC at 400 mA
14.9 VDC at 800 mA
​Connector Type
​2-pin circular Amphenol
​​2-pin circular Amphenol ​​2-pin circular Amphenol
*Charges up to five batteries simultaneously.
**Contact factory for 240 VAC/50Hz input voltage.


  

Clamp-on 12V Chargers

This charger constantly monitors 12 volt/6 Amp charge status, shuts down when charging is complete, and gives notification via LED.

12 Volt 6 Amp Charger
 

​12 Volt, 6 Amp*

​Input Voltage
​120 VAC at 60 Hz**
​Output Voltage
​12 VDC at 6 A
​Recommended Use
​For use with Teledyne ISCO Model 948 or other 12-Volt lead-acid batteries.
​​*Specifically compatible with Model 948 batteries.
**Contact factory for 240 VAC/50Hz.


 

Solar-powered Chargers

Teledyne ISCO's solar-powered chargers deliver energy in long-term applications where AC power isn't available. Units are selected from a variety of solar panel options to best suit your specific application. These chargers are recommended for remote or long-term installations at sites without available AC power.​

​Nickel-Cadmium

​Lead-Acid ​ ​ ​

Model 934​ ​Model 945
​Model 946
​Model 947
​Model 948
​Model 961


 

Model ​963

​Model 965

​12 Volt, 6 Amp

​Model 913


 

​Model 923

 Recommended.
 Requires Lantern Battery Charger Adapter. Contact Teledyne ISCO for details.
 Requires a connector. Contact Teledyne ISCO for details.

​ 

Documentation

In-depth information can be found within the Power Products Brochure, the Power Products Guide, or by contacting Teledyne ISCO or an authorized Teledyne ISCO representative.​